The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMe™ force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
With generous travel, clearance, and depth dimensions, a wide range of tests can be performed, including break testing, cycling, limit testing to a load or distance, loadholding, elongation testing, tensile testing, compression testing, and more. Satisfy various test methods through an easy-to-use menu, allowing the configuration of test speed, force and distance limits, cycling, preload, and many other functions, all protected by a password. Save up to 50 profiles to accommodate a range of test methods.
When the ESM303’s clearance is insufficient for the application, its modular mechanical design allows for single- and double-column extensions. Modularity extends to the controller functions as well. Individual functions, such as travel measurement, cycling, loadholding, etc., may be purchased either upfront or enabled in the field through an activation code. This a-la-carte platform allows for custom configuration as appropriate for the application and budget.
Collect force and travel data, plot and analyze the results, and control test stand motion via PC-based MESUR™gauge Plus software. Or, fully control the stand by a PC through a custom-written program in any language supporting ASCII communications.
|
| |
- Selectable speed setting
- Upper and lower travel limit switches
- Adjustable, removal controller with intuitive menu navigation
- Password protection of test parameters
- Stepper motor-driven, producing smooth and quiet operation with no speed variation under load
- USB output of force vs. time or force vs. travel
- Compact footprint, suitable for crowded workbenches
- Ergonomic design, with smart, clean cable management
- Integrated electronics assembly, easily removed and transported
- Adjustable mounting plate with T-slot base
|
| |
 |
| |
 | |
Note: MESUR™gauge Plus does not require any optional test stand functions, such as PC Control. If force vs. travel vs. time output is required, order the Travel Indication option. See below section for details.
|
 | | A wide range of force gauges and gripping fixtures |
 | | Interface cable, gauge to test stand
Connects Series 7, 5 and Series 4 force gauges to the crosshead. This single cable is used to transmit data and power. The gauge's AC adapter is not required. |
 | | USB cable, test stand to PC (09-1158)
For force and travel data output and PC control. |
 | | Load cell / indicator adapter (AC1062)
Accommodates any Mark-10 indicator and Series R01 or R03 force sensors. Includes mounting hardware. |
 | | Load cell hardware kit
Set of mounting hardware to mount any Series R01 load cell up to 2,000 lbF capacity and any Series R03 force sensor. Can also be adapted to other manufacturers' load cells with #10-32, 1/4-28, and 1/2-20 mounting threads. Note that Series R01 and R03 load cell part numbers ending in -1 (ex: MR01-500-1) include mounting hardware for an ESM303. |
 | |
Single column extensions (ESM303-001-1 / -2 / -3)
Increase the vertical clearance for tall samples. Multiple extensions may be stacked for very long samples.
Three lengths are available - 6, 12 and 24 in [150, 300, and 600 mm].
|
 | | Double column extensions (ESM303-002-1 / -2 / -3)
Accommodate up to a 20 in. [508 mm] wide sample, or ø21.5 in [ø546 mm] round sample. Three heights are available - 6, 12 and 24 in [150, 300, and 600 mm]. Base contains rows of T-slots for fixture mounting. |
 | | Eye end adapters
Allow for quick grip installation and removal, and prevent grip rotation. Mount to common test frames, load cells, and force gauges. |
| | | |
 |
| | | | | |
Any of the below functions may be purchased at time of order or may be enabled in the field at a later date though a code activation process. The only exception is the AF009 travel measurement option, which also requires field hardware installation.
A complete options package is also available, including all of the below features at a discounted price.
The test stand is shipped in Demo Mode, during which time all available features are temporarily enabled for 160 hours of operation.
|
| | | | | |
| Feature | Part No. | Description |  | Requirements |
| FollowMe™ | AF008 | Crosshead movement responds to manually pushing or pulling on the force gauge shaft or load cell. Increasing force produces greater speeds. Ideal for setups and quick positioning. | |
- Series 7 or 5 gauge or indicator with load cell
- 09-1214 interface cable
|
| Travel indication | AF009 | Travel is indicated on the control unit display, with output via USB. An internal scale utilizing Renishaw technology produces significantly higher accuracy than with conventional rotary encoder-based designs. Backlash and nonlinearity are virtually eliminated. | |
- If data output to a PC is required, add 09-1214 and 09-1158 cables, and a Series 7 or 5 gauge or indicator with load cell.
- Field activation requires hardware installation. Otherwise, hardware is factory installed at time of order.
|
| Computer control | AF010 |
The ESM303 may be fully controlled by a PC through a custom-written program in any language supporting ASCII communications. Also responds to the legacy Chatillon TCD command set and legacy Nexygen TCD software (not available from Mark-10).
| |
- Series 7 or 5 gauge or indicator with load cell
- AF009 travel indication
- AF011 programmable travel set points
- 09-1214 interface cable
- 09-1158 USB output cable
|
| Programmable travel limits | AF011 | The stand stops at or cycles between programmable upper and lower travel distances. | |
- AF009 travel indication option
|
| Overload protection | AF012 | Protects a force gauge or force sensor against overload. Program the desired percentage of full scale of the gauge. Adjustable analog voltage setting allows the stand to interface with virtually any gauge with analog output. | |
- Series 7 or 5 gauge or indicator with load cell
- 09-1214 interface cable
|
| Auto return | AF013 | The crosshead moves to a limit switch, force set point, travel position, or break, then stops and reverses direction at full speed to the opposite limit. | |
- If reversing at force set point: Series 7 or 5 gauge or indicator with load cell, and 09-1214 interface cable
- If reversing at travel limit: AF011 programmable travel limits option
- If reversing at break: AF019 break detection option and 09-1214 interface cable
|
| Cycling / dwell time | AF014 | Same as auto return, but with the ability to program up to 100,000 cycles. Programmable dwell time for upper and lower limits (set independently) can be set up for up to 10,000 seconds. | |
- Same as auto return, at the same speed in each direction. Add AF016 for independent up and down speeds.
|
| Independent Up and Down speeds | AF016 | Configurable speeds for up and down directions. | |
-
|
| Low speed extension | AF017 | Extends the standard speed range down to 0.02 in/min (0.5 mm/min). | |
-
|
| High speed extension | AF018 | Extends the standard speed range up to 45 in/min (1,100 mm/min). | |
-
|
| Break detection | AF019 | Crosshead stops at a sudden drop in force. Programmable percentage of peak force. | |
- Series 7 or 5 gauge or indicator with load cell
- 09-1214 interface cable
|
| Loadholding | AF020 | Dynamically adjusts the crosshead position to maintain a programmed load for an indefinite or specified period of time. | |
- Series 7 or 5 gauge or indicator with load cell
- If a specified time is required, add AF014 cycling / dwell time option
- 09-1214 interface cable
|
| Preload / sample touch | AF021 | Stops the crosshead and/or zeroes the travel display at an initial preload - useful in tensile, compression, spring, elongation, and other applications. Preload is programmable as a percentage of force gauge/load cell full scale. Three modes: (1) stop, (2) stop and zero, and (3) zero without stopping. | |
- AF009 travel indication
- Series 7 or 5 gauge or indicator with load cell
- 09-1214 interface cable
|
| Profiles | AF022 | Save and recall sets of test parameters, such as speeds, travel limits, preloads, etc. Up to 50 profiles may be stored. | | - |
| Complete options package | AFCOMP | Includes all functions listed above, plus 09-1214 interface cable and 09-1158 USB cable.
Requires a Series 7 or 5 gauge or indicator with load cell. |
| | |
 |
| | | |
 | |
The ESM303 test stand is shipped as shown at left, and includes the following accessories:
|
 |
| |
| Load capacity: |  | 300 lbF (1.5 kN) @ up to 24 in/min (610 mm/min)
200 lbF (1 kN) @ >24 in/min (610 mm/min) |
| Maximum travel distance: | | 18.0 in (457 mm) |
| Speed range: | | Standard: 0.5 - 13 in/min (13 - 330 mm/min)
Optional: 0.02 - 45 in/min (0.5 - 1,100 mm/min) |
| Speed setting accuracy: | | ±0.2% of setting |
| Speed variation with load: | | ±0% (stepper motor driven) |
| Travel accuracy*: | | ±0.002 in. per 10 in. (±0.05 mm per 250 mm) |
| Travel resolution: | | 0.001 in / 0.02 mm |
| Limit switch repeatability: | | 0.001 in (0.03 mm) |
| Power: | | Universal input 80-240 VAC, 50/60 Hz |
| Weight: | | 56.5 lb (25.6 kg) |
| Warranty: | | 3 years [see individual statement for further details] |
| | | |
| * Because load cell deflection and system deflection are present and not automatically compensated for, this equipment is recommended for applications requiring at least 0.2 in [5 mm] of travel distance. |
| |
|
|
|
Không có nhận xét nào:
Đăng nhận xét